EDX-10 Series
Compact Recording System

  • CE

EDX-10series

Summary

· Compact & lightweight
· With stacked connection, no synchronization cable is required, therefore wiring-saving.
· Synchronous sampling up to 20 kHz for 4 channels
· Sensors can be easily connected with input cables or input adapters.

Features

The EDX-10 Series is measuring instrument, which can measure strain, voltage, and temperature (Thermocouples) simply by connecting a PC via USB interface.
Up to 4 measuring units for 16 channels can be powered by USB interface, no separated power supply is required.

Products table

All display

EDX-10B
Control Unit

EDX-10B
  • CE

Specifications

Interfaces USB
Number of Installed Measuring Units Max. 4 (16 channels)
Sampling Sampling Frequencies : 1 Hz to 20 kHz for 1 to 4 channels measurement
1 Hz to 10 kHz for 1 to 8 channels measurement
1 Hz to 5 kHz for 1 to 16 channels measurement
Operating Temperature 0 to 40ºC
Power Supply 5 VDC by USB bus power or an adapter
Note:
1. When power supply from a USB port, please connect the EDX-10B to the PC directly. No USB hub is required.
2. The adapter can operate any 4 measuring units.
Current Consumption 140 mA or less (5 VDC)
Weight Approx. 170 g
Dimensions 84.0 W x 26.6 H x 84.0 D mm (Excluding protrusions)
Applicable Standard
EMC Directive EN61326-1 (Class A)
RoHS Directive EN50581
Standard Accessories USB cable N-38 (1 m)
Ground wire P-72 (5 m)
Dynamic data acquisition software DCS-100A (CD-ROM)

Optional Accessories

Optional Accessories AC adapter UN310-0515

Specifications

Holding Setting Conditions 141 mA or less (5 VDC)
Storage Measured data is saved in the PC as KS2 file
Channel Conditions Measurement ON/OFF, mode, range, LPF, balance, calibration coefficient, offset, unit, CH name, measuring range, decimal point, rated capacity, rated output, chk.val.(Up), chk.val. (Down) (Selection of any display item is possible)
Setting Measuring Conditions Measuring Mode : Manual, manual (Preset data points), interval,
and analog triggers
Measurement Modes Manual Measurement : Measurement is made from a press of the REC
button to a press of the STOP button or to completion of recording to the preset points.
Interval Measurement : Measurement is made automatically at preset intervals from the preset starting time.
Analog Trigger Measurement : Start and/or stop recording based on the specified trigger conditions.
End trigger: Settable
Delay: Both start and stop, max. 262144 data items/channel
Delay differs with the number of measurement channels
Trigger channels: Any 1 channel
Trigger level: Sets in physical quantity
Trigger slope: Up, down

Dimensions

EDX-10B

EDX-11A
Strain measuring unit

EDX-11A
  • CE

Specifications

Applicable Sensors Strain-gage transducers, Strain gage (Bridge box used)
Input Channels 4
Measurement Range 10000, 50000 μm/m (2 ranges)
Applicable Bridge Resistance 120 Ω to 1 kΩ
Bridge Power Supply 2 VDC
Gage Factor 2.00 fixed
Range Accuracy Each range within ±0.3%FS
Nonlinearity Within ±0.1% FS
A/D Resolution 24-bit
Frequency Response DC to 2 kHz
LPF Transfer Characteristics : 2nd order Butterworth
Cutoff Frequency : Low (100 Hz), High (2 kHz)
Operating Temperature 0 to 40ºC
Input Connectors D-sub 37 pin connector
Power Supply 5 V DC supplied by control unit
Current Consumption 180 mA or less (120 Ω load with all channels connected, at power source DC5 V)
Dimensions 84.0 W x 26.6 H x 84.0 (D) (Mm) (Excluding protrusions)
Weight Approx. 150 g
Applicable Standard
EMC Directive EN61326-1 (Class A)

Standard Accessories

Standard Accessories Strain input cable U-124 (30 cm)
Connection screw M3x5 2 pieces
Rubber foot 8 pieces/sheet

Optional Accessories

Optional Accessories Bridge box coupling cable U-126 (50 cm)
Input adapter UI-51A
One-touch type input adapter UI-52A
The bridge adapter for Quarter bridge system UI-53A-120/350
The bridge adapter for Quarter bridge system UI-54A-120/350
One-touch type input adapter UI-55A
Input Connector Set EDX10-DSUB

Specifications

Holding Setting Conditions 181 mA or less (120 Ω load with all channels connected, at power source DC5 V)

Dimensions

EDX-11A

EDX-12A
Voltage measuring unit

EDX-12A
  • CE

Specifications

Applicable Sensors Voltage
Input Channels 4 (Single end)
Measurement Range 10 V, 50 V (2 ranges)
Range Accuracy Each range within ±0.3%FS
Nonlinearity Within ±0.1% FS
A/D Resolution 24-bit
Frequency Response DC to 2 kHz
LPF Transfer Characteristics : 2nd order Butterworth
Cutoff Frequency : Low (100 Hz), High (2 kHz)
Operating Temperature 0 to 40ºC
Input Connectors D-sub 37 pin connector
Power Supply 5 V DC supplied by control unit
Current Consumption 110 mA or less (5 V DC)
Dimensions 84.0 W x 26.6 H x 84.0 (D) (Mm) (Excluding protrusions)
Weight Approx. 150 g
Applicable Standard
EMC Directive EN61326-1 (Class A)

Standard Accessories

Standard Accessories Input adapter UI-51A
Connection screw M3x5 2pieces
Rubber foot 8 pieces/sheet

Optional Accessories

Optional Accessories BNC input cable U-125 (30 cm)
Bridge box coupling cable U-126 (50 cm)
One-touch type input adapter UI-52A
Input Connector Set EDX10-DSUB

Specifications

Holding Setting Conditions 111 mA or less (5 V DC)

Dimensions

EDX-12A

EDX-13A
Thermocouple measuring unit

EDX-13A
  • CE

Specifications

Applicable Sensors Thermocouples
Input Channels 4
Applicable Thermocouples K, T, J, N (Resistance of thermocouples: 1 kΩ or less)
Measurement Range K: -200.0 to 1370.0ºC
T: -200.0 to 400.0ºC
J: -200.0 to 1200.0ºC
N: -200.0 to 1300.0ºC
Resolution 0.1ºC
Measurement Accuracy K : -200.0 to -100.0ºC or less: ± (0.2% of reading + 0.6ºC)
-100.0 to 400.0ºC: ± (0.1% of reading + 0.4ºC)
T : -200.0 to -100.0ºC or less: ± (0.2% of reading + 0.6ºC)
-100.0 to 1300.0ºC: ± (0.1% of reading + 0.4ºC)
J : -200.0 to -100.0ºCor less: ± (0.2% of reading + 0.6ºC)
-100.0 EC34: ± (0.1% of reading+0.4ºC)
N : -200.0 to -100.0ºCor less: ± (0.2% of reading + 0.6ºC)
-100.0 to 1200.0ºC: ± (0.1% of reading+0.4ºC)
Accuracy of Internal Reference Contact Compensator Accuracy of internal reference contact compensator
±1.0ºC〔Input terminal temperature at equilibrium〕 〔Ambient temperature range: 25±10ºC〕
*Mount the EDX-13A on the bottom when using it with measuring units other than the EDX-13A.
±2.0ºC〔Input terminal temperature in equilibrium〕
For temperatures other than those in the ambient temperature and operating temperature ranges described above.
Check Functions Burnout check
A/D Resolution 24-bit
Sampling Sampling Method : Scanning
Inside Samping Frequencies Approx. 0.5 Hz, Approx. 2.0 Hz
Operating Temperature 0 to 40ºC
Input Connectors Threaded connection type terminal box
Power Supply 5 V DC supplied by control unit
Current Consumption 120 mA or less (5 V DC)
Dimensions 84.0 W x 26.6 H x 84.0 (D) (Mm) (Excluding protrusions)
Weight Approx. 130 g
Applicable Standard
EMC Directive EN61326-1 (Class A)

Standard Accessories

Standard Accessories Terminal box 1 piece
Screwdriver 1 piece
Rubber foot 8 pieces/sheet

Specifications

Holding Setting Conditions 121 mA or less (5 V DC)

Dimensions

EDX-13A

EDX-14A
Strain Measuring Unit

EDX-14A
  • CE

Specifications

Applicable Sensors Strain-gage transducers, strain gages*
*Bridge boxes are required for strain measurement
Output Channels 4
Measurement Range 10 k, 50 k μm/m, 2 steps
Applicable Bridge Resistance 120 Ω to 1 kΩ
Bridge Power Supply 1 VDC
Gage Factor 2.00 fixed
Range Accuracy Each range within ±0.3%FS
Nonlinearity Within ±0.1%FS
A/D Resolution 24 bits
Frequency Response DC to 2 kHz
LPF Transfer Characteristics : 2nd order Butterworth
Cutoff frequencies: 100 Hz, 2 k Hz
Operating Temperature 0 to 40ºC
Input Connectors D-sub 37-pin connector
Power Supply 5 VDC supplied by control unit
Current Consumption 140 mA or less (120 Ω load with all channels connected, at power supply 5 VDC)
Weight Approx. 150 g
Dimensions 84.0 W x 26.6 H x 84.0 D mm (Excluding protrusions)
Applicable Standard
EMC Directive EN61326-1 (Class A)
RoHS Directive EN50581
Standard Accessories Strain input cable U-124 (30 cm)

Optional Accessories

Optional Accessories Bridge box connection cable U-126 (50 cm)
Input Connector Set EDX10-DSUB
Input adapter UI-51A
One-touch type input adapter UI-52A
Bridge adapter for quarter bridge system UI-53A-120/350
Bridge adapter for quarter bridge system UI-54A-120/350
One-touch type input adapter UI-55A

Specifications

Holding Setting Conditions 141 mA or less (120 Ω load with all channels connected, at power supply 5 VDC)

Dimensions

EDX-14A

EDX-15A
Strain/Voltage Measuring Unit

EDX-15A
  • CE

Specifications

Applicable Sensors Strain-gage transducers, strain gages*, voltage (Unbalanced)
*Bridge boxes are required for strain measurement
Output Channels 4
Measurement Range 10 k, 50 k μm/m, 2 steps
10, 50 V
Applicable Bridge Resistance 120 Ω to 1 kΩ
Bridge Power Supply 1 VDC
Gage Factor 2.00 fixed
Range Accuracy Each range within ±0.3%FS
Nonlinearity Within ±0.1%FS
A/D Resolution 24 bits
Frequency Response DC to 2 kHz
LPF Transfer Characteristics : 2nd order Butterworth
Cutoff frequencies: 100 Hz, 2 k Hz
Operating Temperature 0 to 40ºC
Input Connectors D-sub 37-pin connector
Power Supply 5 VDC supplied by control unit
Current Consumption 150 mA or less (120 Ω load with all channels connected, at power supply 5 VDC)
Weight Approx. 150 g
Dimensions 84.0 W x 26.6 H x 84.0 D mm (Excluding protrusions)
Applicable Standard
EMC Directive EN61326-1 (Class A)
RoHS Directive EN50581
Standard Accessories Strain input cable U-124 (30 cm)
Conversion adapter FV-1A x4

Optional Accessories

Optional Accessories Bridge box connection cable U-126 (50 cm)
Input Connector Set EDX10-DSUB
Input adapter UI-51A
One-touch type input adapter UI-52A
Bridge adapter for quarter bridge system UI-53A-120/350
Bridge adapter for quarter bridge system UI-54A-120/350
One-touch type input adapter UI-55A

Specifications

Holding Setting Conditions 151 mA or less (120 Ω load with all channels connected, at power supply 5 VDC)

Dimensions

EDX-15A

Page Top

Download