EDX-200A-2H/4H/4T Option Cards

  • CE

edx-optional_card

Summary

· Measures CAN data and GPS information.
· With 8-bit digital I/O

Features

The ECAN-40A, ETIM-40A, and EGPC-40A are optional cards for EDX-200A. The cards can measure CAN data or GPS information without reducing the number of analog channels and sampling frequencies.

Products table

All display

ECAN-40A
Multichannel CAN Card

  • CE

Specifications

Applicable Models EDX-200A-4H
EDX-200A-2H
(Installed in option slot)

*For EDX-200A-4T, please use ECAN-40A M72.
CAN Ports 2 (High-speed CAN/low-speed CAN selectable)
Channels Up to 512
(Total for 2 ports)
Compatible CAN Input Channels CAN 2.0 A/B(Conforming to ISO-11898, ISO-11519-2)
Baud Rates High speed CAN
1000, 800, 500, 250, 125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps]

Low speed CAN
125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps]
CAN Data Output Output at start:
Output any given CAN data when AD conversion starts

Output at stop:
Output any given CAN data when AD conversion stops

Manual output:
Output any given CAN data at an arbitrary timing.

Interval output:
Output any given CAN data in a predetermined fixed cycle.
Digital I/O
I/O Points Max. 8
I/O Settings Switch among digital input, digital output and remote-controlled input for each bit
(Common applied to all).

*Remote control input: Start and stop measuring, execute BAL, etc.
Input Type Isolated type, TTL level input
Input Voltage Max. 5 VDC
Isolation Methods Digital isolator
Output Type Isolated type, open collector type output
(With 10 kΩ internal pull-up resistors)
Output Voltage 5 VDC
Output Current 25 mA max. (Per point)
Isolation Methods Digital isolator
Connector Type CAN port: D-sub connector (Male) 9-pin

Digital I/O port: MDR connector (Female) 14-pin
Operating Temperature 0 to 50°C, ECAN-40A M72 is -20 to 65°C
Operating Humidity 20 to 90% (Non-condensing)
Storage Temperature -20 to 60°C, ECAN-40A M72 is -30 to 70°C
Dimensions 22.0 W x 128.0 H x 221.5 D mm
Weight Approx. 170 g
Compliance Directive 2014/30/EU (EMC)
Directive 2011/65/EU, (EU)2015/863
(10 restricted substances) (RoHS)
  Note: When using EDX-200A and DCS-101A for arithmetic operation, no CAN measurement is possible.
Standard Accessories Connector plug for digital I/O ports
Shell case
CANdb File Read Optional Software DCS-105A

ETIM-40A
Time Synchronization Card

ETIM-40A
  • CE

Specifications

Applicable Models EDX-200A-4H
EDX-200A-2H
(Installed in option slot)

*For EDX-200A-4T, please use ETIM-40A M72.
Synchronization Synchronizes the recording start time of remote EDX-200A units by using the time data received from GPS satellites.
GPS Data Latitude, longitude, elevation, course over ground,speed, time, receiving conditions, the number of satellites in use, etc.
Saving format: NMEA format
Digital I/O
I/O Points Max. 8
I/O Settings Switch among digital input, digital output and remote-controlled input for each bit
(Common applied to all).

*Remote control input: Start and stop measuring, execute BAL, etc.
Input Type Isolated type, TTL level input
Input Voltage Max. 5 VDC
Output Type Isolated type, open collector type output
(With 10 kΩ internal pull-up resistors)
Output Voltage 5 VDC
Output Current 25 mA max. (Per point)
Isolation Methods Digital isolator
Connector Type GPS sensor port: D-sub connector (Male) 9-pin

Digital I/O port: MDR connector (Female) 14-pin
Operating Temperature 0 to 50°C
ETIM-40A M72 is −20 to 65°C
Operating Humidity 20 to 90% (Non-condensing)
Storage Temperature −20 to 60ºC
ETIM-40A M72 is −30 to 70ºC
Dimensions 22.0 W x 128.0 H x 221.5 D mm
Weight Approx. 160 g
Compliance Directive 2014/30/EU (EMC)
Directive 2011/65/EU, (EU)2015/863
(10 restricted substances) (RoHS)
Standard Accessories Connector plug for digital I/O ports
GPS sensor (Cable length: 5 m)
Shell case

EGPC-40A
GPS/Multichannel CAN Card

EGPC-40A
  • CE

Specifications

Applicable Models EDX-200A-4H
EDX-200A-2H
(Installed in optional slot)

*For EDX-200A-4T, please use EGPC-40A M72.
I/O Ports GPS/CAN Shared Port 1 Dsub connector 9 pins (male)
CAN only port 1 Dsub connector 9 pins (male)
Digital I/O port 1 MDR connector 14 pins (female)
Channels Up to 512
Compatible CAN Versions CAN 2.0A/B
(Conforming to ISO-11898, ISO-11519-2)
Baud Rates High speed CAN:
1000, 800, 500, 250, 125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps]

Low speed CAN:
125, 100, 83.3, 62.5, 50, 33.3, 25, 20, and 10 [kbps]
CAN Data Output Output at start:
Output any given CAN data when AD conversion starts

Output at stop:
Output any given CAN data when AD conversion stops

Manual output:
Output any given CAN data at an arbitrary timing.

Interval output:
Output any given CAN data in a predetermined fixed cycle.
GPS Data Latitude, longitude, elevation, course over ground,speed, time, receiving conditions, the number of satellites in use, etc.
Saving format: NMEA format
Synchronization Synchronizes the recording start time of remote EDX-200A units by using the time data received from GPS satellites.
Digital I/O
I/O Points Max. 8
I/O Settings Switch among digital input, digital output and remote-controlled input for each bit
(Common applied to all).

*Remote-controlled input: Start and stop measuring, execute BAL, etc.
Input Type Isolated type (Digital isolator), TTL level input
Input Voltage Max. 5 VDC
Output Type Isolated type (Digital isolator)
Open collector type output
(With 10 kΩ internal pull-up resistors)
Output Voltage 5 VDC
Output Current 25 mA max. (Per point)
Operating Temperature 0 to 50ºC
EGPC-40A M72 is -20 to 65ºC
Operating Humidity 20 to 90% (Non-condensing)
Storage Temperature -20 to 60ºC
EGPC-40A M72 is -30 to 70ºC
Dimensions 22.0 W x 128.0 H x 221.5 D mm
Weight Approx. 170 g
Compliance Directive 2014/30/EU (EMC)
Directive 2011/65/EU, (EU)2015/863
(10 restricted substances) (RoHS)
  When using EDX-200A and DCS-101A for arithmetic operation, no CAN measurement is possible.
Standard Accessories Connector plug for digital I/O ports
GPS sensor (Cable length: 5 m)
Shell case
CANdb File Read Optional Software DCS-105A

Page Top

eBook

Download