DIS-7200 Series
Non-G-Resistant Data Acquisition System for Crash Test

  • TEDS

DIS-7200 Series

Summary

● Performs pretty much equal to DIS-7000 Series.
● For component tests, dummy qualification tests, airbag ignition tests, and for measuring barrier load cells.

Features

● Compact & lightweight
● Modularization structure enables to optimize your system.
 (From 1 to multi-channel measurements.)
● Outputs ignition current based on the pre-set delay time. (DIA-708AS3)
● Synchronous measuring channels up to 1056
 (Up to 999 channels when using DIS-70A)

Contents

■Master Module
 DIS-7200AS2
■Slave Modules
 DIS-708AS1-T (Signal Conditioner Module, 8 channels)
 DIS-716AS1-T (Signal Conditioner Module, 16 channels)
 DIS-724AS1-T/L (Signal Conditioner Module, 24 channels)
 DIA-708AS3 (Airbag Timer Module)
■Control Software
 DIS-70A

Block diagrams

DIS-7200 Series

Products table

All display

DIS-7200AS2
Master Module

DIS-7200 Series

Specifications

Slave Connection
Targets Slave modules of the DIS-7200 series
Number of Units Max. 15
Input/Output Connector
LAN Connector 1 (0B series, LEMO made)
Connects the PC via a communication cable.
[DC=IN] Connector 1 (2B series, LEMO made)
Connects the (Kyowa's recommended) external power supply via the power cable.
[TRIGGER IN] Connector 1 (1B series, LEMO made)
Connects trigger input cables including tape switches.
[CONT.] Connector 2 (0B series, LEMO made)
Connects master modules via a cascade cable.
Connects the external LED unit for the DIS-7000.
[EXP. CONT. OUT] Connector 1 (1B series, LEMO made)
Connects the conventional products via a cascade cable.
[DIGITAL IN 1/2] Connector 2 (2B series, LEMO made)
Connects a digital input cable or digital input junction box.
[TRIGGER OUT] Connector 4 (1B series, LEMO made)
Connects cameras, etc. via trigger distribution output cables.
[DOWN] Connector 1 (D-sub connector, Japan Aviation Electronics Industry, Limited)
Connects a slave module directly.

*Cables and various devices, connected to the above connectors, are optional accessories.
Switch
[POWER] Switch Turns ON/OFF the DIS-7200AS2 and modules, connected to the DIS-7200AS2.
[SELECT] /[ENTER] Switch Selects the LED indicator description.
LED Indicator/Buzzer
LED Status LED
LED Indicator Indicates the DIS-7200AS2 status and modules statuses, connected to the DIS-7200AS2 in 8 alphanumeric.
Buzzer Built-in alarm buzzer
Status Output Connects the external LED unit (optional accessory) for the DIS-7000.
The external LED unit indicates statuses (waiting for the trigger, recording, error).
Digital Input
Channels 16 × 2 (Total 32)
Input Formats Non-voltage contact
Sampling Method All channels synchronization
Sampling Frequencies 100, 200, 500, 1 k, 2 k, 5 k, 10 k, 20 k, 50 k, 100 kHz
Synchronous Operation
Method Trigger
Trigger Type Switch Trigger : Non-voltage contact input: 2 (Isolated input)
Cascade Trigger : Operated by cascade signals issued from the other units.
Software Trigger : Operated by commands issued from a control software.
Number of Units Max. 48 (Including up to 4 master modules)
Each master module controls 15 slave modules (max).
Connection Method [Between Master Modules]
 Through a cascade cable (Up to 10 m)

[Between Master Module (or Slave Module) and Slave Module]
 ・ Direct connection through a D-sub connector
 ・ Through an extension cable for modules (Up to 2 m)
 *Excluding the power supply.

[Between Master Module and Conventional Product]
 Through a cascade cable (Up to 10 m)
 (Able to use the conventional cascade cables.)
Data Recorder
Mode [Ring buffer mode]
Recognizes the switch trigger 1 or switch trigger 2 as the “Event point” and records data before and after the “Event point.”

[Recorder mode]
Records data from the point where the switch trigger 1 is recognized and handles the switch trigger 2 as the “Event point.”
Memory Type Flash memory
Memory Capacity 500 M data/channel
Recording Time Approx. 80 min (at 100 kHz)
Trigger Distribution Output
Channels 4
Format Each channel has the following 3 formats.
・ Open collector (ON: Closed): Up to 24 V/30 mA
・ TTL (Positive logic 0 V → 5 V): Up to 15 mA
・ TTL (Negative logic 5 V → 0 V): Up to 15 mA
Timing Sets a delay time, required for outputting after recognizing trigger inputs, of each channel.
Range Real time or 0.1 to 9999 ms
Less than 100 ms: 0.1 ms step
100 ms or more, less than 1000 ms: 1 ms step
1000 ms or more, 9999 ms or less: 10 ms step
Accuracy Less than 100 ms: Within ±20 μs
100 ms or more, less than 1000 ms: Within ±200 μs
1000 ms or more, 9999 ms or less: Within ±2.0 ms
*The trigger output timing may delay due to level trigger operations.
Check Functions Memory check
Trigger check
Interfaces Conforming to 10BASE-T/100BASE-TX
Log Function Records the DIS-7200AS2 operating statuses (including power supply and trigger).
Environmental Conditions
Operating Temperature 0 to 50°C
Operating Humidity 20 to 80% (Non-condensing)
Storage Temperature -10 to 60°C
Storage Humidity 10 to 90% (Non-condensing)
Power Supply
Input Range 15 to 28 VDC (TYP.24 V)
*Make sure the external power supply (optional accessory) is 24 VDC.
Or, some items (including the number of units) do not meet the specifications.
Current Consumption Max. 300 mA
(Power supply: 24 VDC, all digital input channels:short circuit)
Others LED Indicator on the Master Module:
Indicates statuses of each module.
External Power Supply:
Kyowa's recommended external power supply only
Appearance
Dimensions Approx. 45 W × 210 D × 100 H mm
(Excluding protrusions and options)
Weight Approx. 1.0 kg

Dimensions

DIS-7200AS2

DIS-708AS1-T
Signal Conditioner Module, 8 channels

DIS-708
  • TEDS

Specifications

Model Square connector type: DIS-708AS1-T(8 channels)
Analog Input
Channels 8
Input Connector 3RT01-RW7F(TAJIMI ELECTRONICS made, applicable plug: 3RT01-PB7M)
Input Format Balanced differential input
Input Resistance Bridge sensor measurement:
 Gain ×1 to 5000 Approx. (50 MΩ + 50 MΩ)
 Gain ×0.1 to 0.9 Approx. (100 kΩ+100 kΩ)

Voltage measurement:
 Approx. (100 kΩ +100 kΩ)
Input Voltage Within ±20 V
Gain ×0.1 to 0.9 (× 0.1 step)
×1 to 5000 (× 1 step)
Gain Accuracy Within ±0.2%FS
Nonlinearity Within ±0.1%FS
Balancing Adjustment Gain
× 0.1 to 0.9: Within ± 20 V
× 1 to 9: Within ± 2 V
× 10 to 99: Within ± 200 mV
× 100 to 5000: Within ± 20 mV
Bridge Excitation
Voltage Apply Method Each channel on/off switchable
Voltage 10, 5, 2 VDC
Within ±0.1%
Bridge Configuration Half bridge system
Full bridge system
Bridge Resistance 120 to 5 kΩ
Current Within 30 mA/channel
LPF
Transfer Characteristic 5th order Butterworth
Cutoff Frequencies 50, 100, 200, 400, 1 k, 2 k, 4 k, 10 k, 20 kHz
Amplitude Ratio at Cutoff Point Within -3 ±1 dB
Attenuation Characteristic Within -30 ±3 dB/oct
AD Converter
Resolution 16 bits
Sampling Method All channels synchronization
Sampling Frequencies 100, 200, 500, 1 k, 2 k, 5 k, 10 k, 20 k, 50 k,100 kHz
S/N Ratio 50 dB or more (Filter: 1 k Hz)
Trigger
Type Cascade trigger:
Operated by cascade signals issued from the other units.

Analog (level) trigger:
Operated by level of arbitrary 3 channels.

Software trigger:
Operated by commands issued from the control software.
Data Recorder
Mode Ring buffer mode
The connected master module recognizes the switch trigger 1 or switch trigger 2 as the “Event point” and records data
before and after the “Event point.”

Recorder mode
The connected master module records data from the point where the switch trigger 1 is recognized and handles the switch trigger 2 as the “Event point.”
Memory Type Flash memory
Memory Capacity 500 M data/channel
Recording Time Approx. 80 min (at 100k Hz)
TEDS Function IEEE1451.4 (Mixed Mode Transducer Interface Class2) supported
Sensor ID supported
Check Functions Bridge excitation check/sensor check
(tip parallel resistance method) / gain check/
input terminal resistance check/open circuit check/
memory check/trigger check
Indicator Status LED
Interface Conforming to 10BASE-T/100BASE-TX
Log Function Records the signal conditioner module operating statuses
(including power supply and trigger).
Environmental Conditions
Operating Temperature 0 to 50°C
Operating Humidity 20 to 80% (Non-condensing)
Storage Temperature -10 to 60°C
Storage Humidity 10 to 90% (Non-condensing)
Power Supply
Input Range 15 to 28 VDC (TYP.24 V)
*Make sure the external power supply (optional accessory) is 24 VDC.
Or, some items (including the number of units) do not meet the specifications.
Current Consumption Max. 250 mA
(Power supply: 24 VDC, bridge excitation: 5 V,load: 350 ohm/8 channels)
Applicable Standards ISO 6487/SAE J211-1
Others The signal conditioner module is turned ON/OFF by the master module.
External power supply: Kyowa's recommendes external power supply only
Appearance
Dimensions Approx. 35 W × 210 D × 100 H mm
(Excluding protrusions and options)
Weight Approx. 0.8 kg

DIS-716AS1-T
Signal Conditioner Module,16 channels

DIS-716AS1-T
  • TEDS

Specifications

Model Square connector type: DIS-716AS1-T(16 channels)
Analog Input
Channels 16
Input Connector 3RT01-RW7F(TAJIMI ELECTRONICS made, applicable plug: 3RT01-PB7M)
Input Format Balanced differential input
Input Resistance Bridge sensor measurement:
 Gain ×1 to 5000 Approx. (50 MΩ + 50 MΩ)
 Gain ×0.1 to 0.9 Approx. (100 kΩ+100 kΩ)

Voltage measurement:
 Approx. (100 kΩ +100 kΩ)
Input Voltage Within ±20 V
Gain ×0.1 to 0.9 (× 0.1 step)
×1 to 5000 (× 1 step)
Gain Accuracy Within ±0.2%FS
Nonlinearity Within ±0.1%FS
Balancing Adjustment Gain
× 0.1 to 0.9: Within ± 20 V
× 1 to 9: Within ± 2 V
× 10 to 99: Within ± 200 mV
× 100 to 5000: Within ± 20 mV
Bridge Excitation
Voltage Apply Method Each channel on/off switchable
Voltage 10, 5, 2 VDC
Within ±0.1%
Bridge Configuration Half bridge system
Full bridge system
Bridge Resistance 120 to 5 kΩ
Current Within 30 mA/channel
LPF
Transfer Characteristic 5th order Butterworth
Cutoff Frequencies 50, 100, 200, 400, 1 k, 2 k, 4 k, 10 k, 20 kHz
Amplitude Ratio at Cutoff Point Within -3 ±1 dB
Attenuation Characteristic Within -30 ±3 dB/oct
AD Converter
Resolution 16 bits
Sampling Method All channels synchronization
Sampling Frequencies 100, 200, 500, 1 k, 2 k, 5 k, 10 k, 20 k, 50 k,100 kHz
S/N Ratio 50 dB or more (Filter: 1 k Hz)
Trigger
Type Cascade trigger:
Operated by cascade signals issued from the other units.

Analog (level) trigger:
Operated by level of arbitrary 3 channels.

Software trigger:
Operated by commands issued from the control software.
Data Recorder
Mode Ring buffer mode
The connected master module recognizes the switch trigger 1 or switch trigger 2 as the “Event point” and records data
before and after the “Event point.”

Recorder mode
The connected master module records data from the point where the switch trigger 1 is recognized and handles the switch trigger 2 as the “Event point.”
Memory Type Flash memory
Memory Capacity 500 M data/channel
Recording Time Approx. 80 min (at 100k Hz)
TEDS Function IEEE1451.4 (Mixed Mode Transducer Interface Class2) supported
Sensor ID supported
Check Functions Bridge excitation check/sensor check
(tip parallel resistance method) / gain check/input terminal resistance check/open circuit check/memory check/trigger check
Indicator Status LED
Interface Conforming to 10BASE-T/100BASE-TX
Log Function Records the signal conditioner module operating statuses
(including power supply and trigger).
Environmental Conditions
Operating Temperature 0 to 50°C
Operating Humidity 20 to 80% (Non-condensing)
Storage Temperature -10 to 60°C
Storage Humidity 10 to 90% (Non-condensing)
Power Supply
Input Range 15 to 28 VDC (TYP.24 V)
*Make sure the external power supply (optional accessory) is 24 VDC.
Or, some items (including the number of units) do not meet the specifications.
Current Consumption Max. 350 mA
Power supply: 24 VDC, bridge excitation: 5 V,load: 350 ohm/16 channels)
Applicable Standards ISO 6487/SAE J211-1
Others The signal conditioner module is turned ON/OFF by the master module.
External power supply: Kyowa's recommendes external power supply only
Appearance
Dimensions Approx. 35 W × 210 D × 100 H mm
(Excluding protrusions and options)
Weight Approx. 0.9 kg

DIS-724AS1-T
Signal Conditioner Module,24 channels

DIS-724AS1-T
  • TEDS

Specifications

Model Square connector type:DIS-724AS1-T(24 channels)
Analog Input
Channels 24
Input Connector 3RT01-RW7F(TAJIMI ELECTRONICS made, applicable plug: 3RT01-PB7M)
Input Format Balanced differential input
Input Resistance Bridge sensor measurement:
 Gain ×1 to 5000 Approx. (50 MΩ + 50 MΩ)
 Gain ×0.1 to 0.9 Approx. (100 kΩ+100 kΩ)

Voltage measurement:
 Approx. (100 kΩ +100 kΩ)
Input Voltage Within ±20 V
Gain ×0.1 to 0.9 (× 0.1 step)
×1 to 5000 (× 1 step)
Gain Accuracy Within ±0.2%FS
Nonlinearity Within ±0.1%FS
Balancing Adjustment Gain
× 0.1 to 0.9: Within ± 20 V
× 1 to 9: Within ± 2 V
× 10 to 99: Within ± 200 mV
× 100 to 5000: Within ± 20 mV
Bridge Excitation
Voltage Apply Method Each channel on/off switchable
Voltage 10, 5, 2 VDC
Within ±0.1%
Bridge Configuration Half bridge system
Full bridge system
Bridge Resistance 120 to 5 kΩ
Current Within 30 mA/channel
LPF
Transfer Characteristic 5th order Butterworth
Cutoff Frequencies 50, 100, 200, 400, 1 k, 2 k, 4 k, 10 k, 20 kHz
Amplitude Ratio at Cutoff Point Within -3 ±1 dB
Attenuation Characteristic Within -30 ±3 dB/oct
AD Converter
Resolution 16 bits
Sampling Method All channels synchronization
Sampling Frequencies 100, 200, 500, 1 k, 2 k, 5 k, 10 k, 20 k, 50 k,100 kHz
S/N Ratio 50 dB or more (Filter: 1 k Hz)
Trigger
Type Cascade trigger:
Operated by cascade signals issued from the other units.

Analog (level) trigger:
Operated by level of arbitrary 3 channels.

Software trigger:
Operated by commands issued from the control software.
Data Recorder
Mode Ring buffer mode
The connected master module recognizes the switch trigger 1 or switch trigger 2 as the “Event point” and records data
before and after the “Event point.”

Recorder mode
The connected master module records data from the point where the switch trigger 1 is recognized and handles the switch trigger 2 as the “Event point.”
Memory Type Flash memory
Memory Capacity 500 M data/channel
Recording Time Approx. 80 min (at 100k Hz)
TEDS Function IEEE1451.4 (Mixed Mode Transducer Interface Class2) supported
Sensor ID supported
Check Functions Bridge excitation check/sensor check
(tip parallel resistance method) / gain check/input terminal resistance check/open circuit check/memory check/trigger check
Indicator Status LED
Interface Conforming to 10BASE-T/100BASE-TX
Log Function Records the signal conditioner module operating statuses
(including power supply and trigger).
Environmental Conditions
Operating Temperature 0 to 50°C
Operating Humidity 20 to 80% (Non-condensing)
Storage Temperature -10 to 60°C
Storage Humidity 10 to 90% (Non-condensing)
Power Supply
Input Range 15 to 28 VDC (TYP.24 V)
*Make sure the external power supply (optional accessory) is 24 VDC.
Or, some items (including the number of units) do not meet the specifications.
Current Consumption Max. 500 mA
(Power supply: 24 VDC, bridge excitation: 5 V,load: 350 ohm/24 channels)
Applicable Standards ISO 6487/SAE J211-1
Others The signal conditioner module is turned ON/OFF by the master module.
External power supply: Kyowa's recommendes external power supply only
Appearance
Dimensions Approx. 35 W × 210 D × 100 H mm
(Excluding protrusions and options)
Weight Approx. 1.0 kg

DIS-724AS1-L
Signal Conditioner Module,24 channels

DIS-724AS1-L
  • TEDS

Specifications

Model Round connector type: DIS-724AS1-L (24 channels)
Analog Input
Channels 24
Input Connector EGG.1B.307(LEMO made, applicable plug: FGG.1B.307)
Input Format Balanced differential input
Input Resistance Bridge sensor measurement:
 Gain ×1 to 5000 Approx. (50 MΩ + 50 MΩ)
 Gain ×0.1 to 0.9 Approx. (100 kΩ+100 kΩ)

Voltage measurement:
 Approx. (100 kΩ +100 kΩ)
Input Voltage Within ±20 V
Gain ×0.1 to 0.9 (× 0.1 step)
×1 to 5000 (× 1 step)
Gain Accuracy Within ±0.2%FS
Nonlinearity Within ±0.1%FS
Balancing Adjustment Gain
× 0.1 to 0.9: Within ± 20 V
× 1 to 9: Within ± 2 V
× 10 to 99: Within ± 200 mV
× 100 to 5000: Within ± 20 mV
Bridge Excitation
Voltage Apply Method Each channel on/off switchable
Voltage 10, 5, 2 VDC
Within ±0.1%
Bridge Configuration Half bridge system
Full bridge system
Bridge Resistance 120 to 5 kΩ
Current Within 30 mA/channel
LPF
Transfer Characteristic 5th order Butterworth
Cutoff Frequencies 50, 100, 200, 400, 1 k, 2 k, 4 k, 10 k, 20 kHz
Amplitude Ratio at Cutoff Point Within -3 ±1 dB
Attenuation Characteristic Within -30 ±3 dB/oct
AD Converter
Resolution 16 bits
Sampling Method All channels synchronization
Sampling Frequencies 100, 200, 500, 1 k, 2 k, 5 k, 10 k, 20 k, 50 k,100 kHz
S/N Ratio 50 dB or more (Filter: 1 k Hz)
Trigger
Type Cascade trigger:
Operated by cascade signals issued from the other units.

Analog (level) trigger:
Operated by level of arbitrary 3 channels.

Software trigger:
Operated by commands issued from the control software.
Data Recorder
Mode Ring buffer mode
The connected master module recognizes the switch trigger 1 or switch trigger 2 as the “Event point” and records data
before and after the “Event point.”

Recorder mode
The connected master module records data from the point where the switch trigger 1 is recognized and handles the switch trigger 2 as the “Event point.”
Memory Type Flash memory
Memory Capacity 500 M data/channel
Recording Time Approx. 80 min (at 100k Hz)
TEDS Function IEEE1451.4 (Mixed Mode Transducer Interface Class2) supported
Sensor ID supported
Check Functions Bridge excitation check/sensor check
(tip parallel resistance method) / gain check/input terminal resistance check/open circuit check/memory check/trigger check
Indicator Status LED
Interface Conforming to 10BASE-T/100BASE-TX
Log Function Records the signal conditioner module operating statuses
(including power supply and trigger).
Environmental Conditions
Operating Temperature 0 to 50°C
Operating Humidity 20 to 80% (Non-condensing)
Storage Temperature -10 to 60°C
Storage Humidity 10 to 90% (Non-condensing)
Power Supply
Input Range 15 to 28 VDC (TYP.24 V)
*Make sure the external power supply (optional accessory) is 24 VDC.
Or, some items (including the number of units) do not meet the specifications.
Current Consumption Max. 500 mA
(Power supply: 24 VDC, bridge excitation: 5 V,load: 350 ohm/24 channels)
Applicable Standards ISO 6487/SAE J211-1
Others The signal conditioner module is turned ON/OFF by the master module.
External power supply: Kyowa's recommendes external power supply only
Appearance
Dimensions Approx. 35 W × 210 D × 100 H mm
(Excluding protrusions and options)
Weight Approx. 1.0 kg

DIA-708AS3
Airbag Timer Module

DIA-708AS3

Specifications

Ignition Current
Output Channels 8
Connectors Mainframe: ECP.0S.302 (LEMO made)
Plug: FFA.0S.302 (LEMO made)
Output Current Setting range: 0.5 to 3.0 A and OFF
 (Selectable with 0.1 A steps)
Accuracy: Within ±0.05 A
Output Voltage Approx. 18 V (Max.)
Load Resistance 1 to 9 Ω (Including cable resistance value to the inflator)

*However, the actual upper limit of the resistance value is obtained from the following.
Set current (A) x Load resistance (Ω) = Max. output voltage 18 V
Output Time Setting range: 0.2 to 5 ms (Selectable with 0.1 ms)

*However,
Set current (A) x Set current (A) x Load resistance (Ω) x Output time (ms) ≤ 180

[Example]
If the preset current 3.0 A and the resistance 6.0 Ω, then the output current is up to 3.3 ms.
If the preset current 2.5 A and the resistance 7.2 Ω, then the output current is up to 4.0 ms.
Delay Time [Setting range]
 0.1 to 999.9 ms (Selectable with 0.1 ms steps)
 1000 to 9999 ms (Selectable with 1 ms steps)

[Accuracy]
 Within ±0.01 ms (When setting 0.1 to 99.9 ms)
 Within ±0.1 ms (When setting 100.0 to 999.9 ms)
 Within ±1 ms (When setting 1000 to 9999 ms)
AD Converter
Resolution 16 bits
Measurement Accuracy Within ±3%FS (FS = 5.0 A)
Sampling Method All channels synchronization
Sampling Frequencies 10 k, 20 k, 50 k,100 kHz
Data Recorder
Mode [Ring buffer mode]
The connected master module recognizes the switch trigger 1 or switch trigger 2 as the “Event point” and records data before and after the “Event point.”

[Recorder mode]
The connected master module records data from the point where the switch trigger 1 is recognized and handles the switch trigger 2 as the “Event point.”
Memory Type Flash memory
Memory Capacity 250 M data/channel
Recording Time Approx. 40 min (at 100k Hz)
Trigger
Type Cascade triggers:
Operated by triggers from the other devices.

Software triggers:
Operated by commands issued from the external PC.
Check Functions Memory check, trigger check, current output check
Safety Functions
Safety Functions In a state with the SAFETY plug inserted to the SAFETY connector, trigger signals must not be input.
In addition, the current output terminals are shorted in the DIA-708AS3 so as not to flow the accidental current to the inflator.
Measuring Load Resistence Apply weak current (Approx. 10 mA) to the inflator and measure the resistance.
(*The measured resistance includes the cable resistance to the inflator. )

Measurement range: 0.0 to 10.0 Ω
Resolution: 0.1 Ω
Accuracy: Within ±0.3 Ω

[Resistance measurement before the test:
Just before conducting the test (when moving the SAFETY plug from the SAFETY connector to UNSAFETY connector), automatically measures the load resistance to detect errors such as cable broken.
Only when the measured result is within the preset resistance range, the DIA-708AS3 becomes waiting for trigger state to continue the test.

[Resistance measurement after the test]:
After completing the ignition, automatically measures the load resistance for detecting the not ignited inflator.
The measured results are displayed on the status LED on the top face.
CH Status Displays the status of the DIA-708AS3 with the LED on the front panel.
Buzzer The built-in buzzer in DIS-7200AS2 issues alarm in the following incident.
 ・ Recharging the capacitor for current output.
 ・ Detects errors when measuring the resistance.
 ・ Detects errors when checking the current output.
Interfaces Conforming to 10BASE-T/100BASE-TX
Log Function Records the DIA-708AS3 operating statuses (including power supply and trigger).
Operating Environment
Operating Temperature 0 to 50 ºC
Operating Humidity 20 to 80 % (Non-condensing)
Storage Temperature -10 to 60 ºC
Storage Humidity 10 to 90% (Non-condensing)
Power Supply
Input Range 15 to 28 VDC (TYP.24 V)
*Make sure the external power supply (optional accessory) is 24 VDC.
Or, some items (including the number of units) do not meet the specifications.
Current Consumption Max. 250 mA (Power supply: 24 VDC)
Others ・The DIA-708AS3 is turned ON/OFF by the master module.
・External power supply: Kyowa's recommended external power supply only
Appearance
Dimensions Approx. 35 W × 210 D × 100 H mm
(Excluding protrusions and options.)
Weight Approx. 0.9 kg

DIS-70A
Control Software for Crash Test

DIS-70A

Specifications

Applicable Models DIS-7200 Series:
DIS-7200AS, DIS-724AS,DIS-716AS, DIS-708AS, DIA-708AS
DIS-7000 Series:
DIS-7000A, DIS-724A, DIA-708A
DIS-600 Series:
DIS-61A, DIS-632A, DIS-618A
DIS-500 Series:
DIS-506A
DIS-5000 Series:
DIS-5010A, DIS-5000A, DIS-5200A,DIS-5210A, DIA-512A
Other Series:
DIS-3000B/A, DIS-3200B/A,DIS-2000A
*Note that abbreviated model may appear on the DIS-70A.
Number of Controllable Units*1 DIS-7200 & DIS-7000 Series: 4 groups
1 group: 1 unit of DIS-7200A or DIS-7000A
15 units of DIS-724AS, DIS-716AS,DIS-708AS, DIA-708AS,DIS-724A, DIA-708A

Other than the DIS-7200 & DIS-7000 Series: 1 group
1 group: 16 units of DIS Series
2 units of DIA-512A
Test Conditions Setting Items Test number, test name, test mode, test objective,
test laboratory, test performer, test comment,
test date, test time, temperature (degree C),
collision angle (degree), collision velocity (km/h),
vehicle model, vehicle number, spec., body type,
engine type, transmission type, vehicle weight (kg)
Channel Conditions Setting Items DIS series:
Test object, target group, target name,seat position, digital filter, polarity,
ISO MME code, sensor type, sensor model,serial number, sensor ID, rated capacity,rated output (or sensitivity), engineering unit,bridge excitation, bridge resistance,expected value (gain or range)*2, coefficient,offset, balance, comment
DIA series:
ON/OFF, test object, seat position, target name,ISO MME code, delay time, output current,output time, resistance,lower limited resistance before test,upper limited resistance before test,lower limited resistance after test,and upper limited resistance after test
Reading Sensor Information*3 TEDS, sensor ID, sensor files
Measurement Condition Setting Items*4 Sampling frequency
Analog filter
Trigger mode
Pre-trigger time
Post-trigger time
External trigger
Cascade trigger
Analog (level) trigger
Delay time of trigger output
Check Functions*5 Gain check
Bridge excitation check
Sensor check
Burnout check
Resistance check
Battery check
Trigger check
Overflow check
Monitoring Functions*6 Real-time numeric value monitoring
Real-time waveform monitoring
Recorded data monitoring
Data File Format Kyowa's original binary, ASCII, and ISO MME
Language English / Japanese
Operation Environment
OS Windows® 8.1, Windows® 10
English/Japanese, 32/64 bits support
If 64-bit OS, operate in WOW64 (Windows 32-bit On Windows 64-bit) environment.
Display Resolution: 1280×768 pixels or more
CPU Core 2 Duo, 2 GHz or more
Memory If 32-bit OS, 2 GB or more (Recommended: 4 GB or more)
If 64-bit OS, 4 GB or more
HDD Approx. 100 MB for installation
Interface DIS-7200, DIS-7000, DIS-600 & DIS-5000 Series:
10/100 BASE-T/TX Ethernet (Conforming to IEEE802.3) Interface
(100 BASE-TX recommended)
DIS-506A: USB 2.0 Interface
DIS-3200A/B: 10 BASE-T Ethernet (Conforming to IEEE802.3) Interface
DIS-3000A/B: 10 BASE2 Ethernet (Conforming to IEEE802.3) Interface
DIS-2000A: GPIB Interface, National Instruments NI GPIB, NI-488.2 software (GPIB driver)
  *1 Up to 999 channels (Total of analog channels, digital channels, and airbag timer channels)
*2 The gain (or range) is automatically calculated based on the expected value.
*3 TEDS and sensor ID: DIS-724AS, DIS-716AS, DIS-708AS, DIS-724A,DIS-632A, DIS-618A, DIS-506A, and DIS-5000 Series only
*4 Above settings are based on the spec. of the target models.
*5 Above check functions are based on the spec. of the target models.
*6 Above monitoring functions are based on the spec. of the target models.

Page Top

Remarks

*Up to 15 units are docked per single master module.
*You cannot connect the DIS-7000 Series modules.