Software of EDX-3000A/B Ver.01.50 (02/18/2020)

Ver.01.50 (02/18/2020)

  • Fixed the following bug.
    When you operated EDX-200A units synchronously, you could not set the “Synchronous cable setting” to “500 m or less” or “1000 m or less” on the DCS-100A.
  • Fixed the following bug.
    When you operated EDX-5000A units synchronously, selected the “BAL.” with “Internal CAL” on the master EDX-5000A, and executed the BAL operation while monitoring data, the amplifier setting contents of the “voltage-mode channels” on the CDV-40B(A) series became invalid.

Preparation

1)Items required

  • A USB memory (128MB or more)
  • A display
  • A USB mouse or a PS/2 mouse

Precautions

Serial number of EDX-3000A/B is required for downloading. The seal of serial number is on the rear panel of the EDX-3000A/B.

Supplementary explanation

At most, there are 3 kinds of media have to update to keep the EDX-3000A/B in the latest version.
Some media don’t have to update depend on the current version. For details, please refer the table below.

Update requirements

You may need to install the following three updates before updating the EDX-3000A/B to the latest version. (Depending on the current version, the updates may not be required. Check below.)

Current EDX application version EDX application update Internal USB driver update EDX firmware & FPGA update
01.16 Required Not required Not required
01.15 Required Not required Not required
01.14 Required Not required Not required
01.13 Required Not required Not required
01.12 Required Not required Required
01.11 Required Not required Not required
01.10 Required Not required Required
01.09 Required Not required Not required
01.08 Required Not required Not required
01.07 Required Not required Required
01.06 Required Not required Required
01.05 Required Not required Required
01.03 Required Required Required
01.02 Required Required Required
*
The firmware version must be updated by Kyowa for versions before Ver. 01.02.

Downloading

  1. Click the [Download] icon on the bottom of this page, and save the zip file into your PC, please.
  2. Select the saved zip file then right click your mouse button, after that select the item of “Extract all files”, please.

Installation procedure

  1. Create a version update USB memory device.
  2. Update the EDX application (EDX application running on the operating system).
  3. Update the internal USB driver (for versions earlier than EDX-3000A Version 01.13).
  4. Update the EDX firmware and FPGA (internal circuit board firmware and FPGA program).
  5. Copy the following files from downloaded folder to a USB memory, please.
  6. USB memory device contents

    E3KUPDT folder EDX firmware and FPGA update files
    E3KUSB folder Internal USB memory driver update files
    setupEDX3000AB_XXXX.exe EDX application update file (XXXX: 0113 for version 01.13)
  7. Refer to the manual in the downloaded folder for updating.

Implementation Note

If the EDX’s application version is 01.03 or earlier, the firmware and the FPGA can’t be updated without updating the internal USB driver.

The file may not be extracted correctly depending on the decompression program. If this is the case, try extracting the file with another decompression software package and installing the software.

  1. The copyright to the software provided in this service (“software”) is owned by Kyowa Electronic Instruments Co., Ltd. or individuals listed as copyright holders.
  2. Unauthorized duplicating, copying, reprinting and changing of the software, in whole or in part, is prohibited by law.
  3. The software may be changed for the purpose of improvement without notice.
  4. Kyowa Electronic Instruments is not liable for any result of saving (downloading) and operating the software.
  5. This service is provided for the customers who use our products applicable to the service.
  6. Before installing the product, please read the agreement below. By installing the product, you are consenting to be bound by and become a party to this agreement. If you do not agree to all of the terms of this agreement, do not install the product and delete the product and its duplicates from your computer memory or hard disk.

Client License Agreement

The customer and Kyowa Electronic Instruments Co., Ltd. (“company”) agree the following concerning the use of the software package (“software”), copyright to which is owned by the company:

Article 1. (License Agreement)

The company grants the customer a license to use the software on a single computer.
The company prohibits the customer from diverting, transferring, selling or leasing the software for any purpose.

Article 2. (Disclaimer of Warranty)

The company makes no warranty as to the quality and performance of the software (*). The company may change the software for improvement without notice. Under no circumstances shall the company be liable for the result of using the software by the customer (*).

(*)
Including but not limited to shareware, freeware, sample programs, and updates.

Agree and download58 MB