Firmware for EDX-5000A Ver.01.23 (10/28/2021)

Upgraded program for the EDX-5000A firmware

Ver.01.23 (10/28/2021)

Fixed the following bug.

  1. When using the conditioner cards with antialiasing LPF (CDV-40A/B-F, DPM-42A/B-F, DPM-42B-I-F, CCA-40A-F, AD-40AS-F), the model and serial No. of the filter PCB didn’t appear.
    The model and serial No. of the filter PCB appears on the following windows.
    • Main Unit Software (ETA-55A): [Ver. Information] window
    • EDX-3000B Compatible Software (ELA-55A): [Detailed information] window
    • Dynamic Data Acquisition Software (DCS-100A): [Detailed information] window

    [Example]

    • Before
      1: CDV-40B-F (ABCDEF012) 001F: 6
    • After
      1: CDV-40B-F (ABCDEF012) 001F: 6 FLB-40A (ABCDEF012) 7FBD
    The FLB-40A is the model of the filter PCB and the ABCDEF012 on the right is the serial No. of the filter PCB.
    The serial No. of the filter PCB is the same as that (ABCDEF012 on the left) of the conditioner card.
  2. Fixed the following bug.
    When you assigned the “Output Manual Cond” function about the CAN data to the OPT. switch – on the EDX-5000A front panel that did not mount the GPS/Multi-channel CAN Module (EGPC-50A) or on the remote control unit (RCU-42A) - by using the Dynamic Data Acquisition Software “DCS-100A” or measuring condition files, the Main Unit Software (ETA-55A) hung.
  3. Fixed the following bug.
    When the master EDX-5000A did not mount the GPS/Multi-channel CAN Module (EGPC-50A), you couldn’t assign the “Output Manual Cond” function about the CAN data to the OPT. switch – on the EDX-5000A front panel or on the remote control unit (RCU-42A) - by using the Main Unit Software “ETA-55A” or EDX-3000B Compatible Software “ELA-55A”.
  4. Before recording the CAN data by using the GPS/Multi-channel CAN Module (EGPC-50A), be sure to check the PDF [UPDATING THE EDX-5000A Ver.01.02] and take the following steps.
    “3.3 Updating the EDX application”

    “3.4 Updating the EDX firmware, FPGA”
    For details, see the [Option embedded software OPTS-55A Ver.01.04].
  5. When the DIO mode was “Remote control unit” and the synchronous operation was “Sync guest” on the EDX-3000B Compatible Software (ELA-55A) of the master unit, the slave mark appeared on the window; nevertheless, the unit did not operate properly as the slave unit.

Option embedded software

  • Fixed the following bug.
    When you selected the CAN 1 port and CAN 2 port at the same time and set the frame IDs of the CAN 1 port by a method other than the ascending order on the received conditions of the ECAN condition settings, the CAN data of the CAN 1 port couldn’t be measured.

Client License Agreement

The customer and Kyowa Electronic Instruments Co., Ltd. (“company”) agree the following concerning the use of the software package (“software”), copyright to which is owned by the company:

Article 1. (License Agreement)

The company grants the customer a license to use the software on a single computer.
The company prohibits the customer from diverting, transferring, selling or leasing the software for any purpose.

Article 2. (Disclaimer of Warranty)

The company makes no warranty as to the quality and performance of the software (*). The company may change the software for improvement without notice. Under no circumstances shall the company be liable for the result of using the software by the customer (*).

(*)
Including but not limited to shareware, freeware, sample programs, and updates.

Agree and download216 MB